ivan
27-04-07, 03:57 PM
MacPherson Strut
This is currently, without doubt, the most widely used front suspension system in cars of European origin. It is simplicity itself. The system basically comprises of a strut-type spring and shock absorber combo, which pivots on a ball joint on the single, lower arm. At the top end there is a needle roller bearing on some more sophisticated systems. The strut itself is the load-bearing member in this assembly, with the spring and shock absorber merely performing their duty as oppose to actually holding the car up. In the rendered image here, you can't see the shock absorber because it is encased in the blue strut tower, inside the spring.
The steering gear is either connected directly to the lower shock absorber housing, or to an arm from the front or back of the spindle or hub assembly (in this case). When you steer, it physically twists the shock absorber housing (and consequently the spring) to turn the wheel. Simple, the spring is seated in a special plate at the top of the assembly which allows this twisting to take place. If the spring or this plate are worn, you'll get a loud 'clonk' on full lock as the spring frees up and jumps into place. This is sometimes confused for CV joint knock.
Potted history of MacPherson: Earle S. MacPherson of General Motors developed the MacPherson strut in 1947. GM cars were originally design-bound by accountants. If it cost too much or wasn't tried and tested, then it didn't get built/used. Major GM innovations including the MacPherson Strut suspension system sat stifled on the shelf for years because innovation cannot be proven on a spreadsheet until after the product has been produced or manufactured. Consequently, Earle MacPherson went to work for Ford UK in 1950, where Ford started using his design on the 1950 'English' Ford models straight away.
This is the front suspension setup we use on the Starlet. It consists of a lower control arm, a hub assembly (which holds the calliper, disk and wheel together) and the strut (shock absorber) with a spring coiled around it.
259 260
Regards,
Ivan
Note: This article may have been copied from another website and revised to better suit the Starlet community. If you are the owner of the original article and would like us to remove it, please contact me via email with the subject "Remove Article" and i will remove it from this website as soon as possible.
This is currently, without doubt, the most widely used front suspension system in cars of European origin. It is simplicity itself. The system basically comprises of a strut-type spring and shock absorber combo, which pivots on a ball joint on the single, lower arm. At the top end there is a needle roller bearing on some more sophisticated systems. The strut itself is the load-bearing member in this assembly, with the spring and shock absorber merely performing their duty as oppose to actually holding the car up. In the rendered image here, you can't see the shock absorber because it is encased in the blue strut tower, inside the spring.
The steering gear is either connected directly to the lower shock absorber housing, or to an arm from the front or back of the spindle or hub assembly (in this case). When you steer, it physically twists the shock absorber housing (and consequently the spring) to turn the wheel. Simple, the spring is seated in a special plate at the top of the assembly which allows this twisting to take place. If the spring or this plate are worn, you'll get a loud 'clonk' on full lock as the spring frees up and jumps into place. This is sometimes confused for CV joint knock.
Potted history of MacPherson: Earle S. MacPherson of General Motors developed the MacPherson strut in 1947. GM cars were originally design-bound by accountants. If it cost too much or wasn't tried and tested, then it didn't get built/used. Major GM innovations including the MacPherson Strut suspension system sat stifled on the shelf for years because innovation cannot be proven on a spreadsheet until after the product has been produced or manufactured. Consequently, Earle MacPherson went to work for Ford UK in 1950, where Ford started using his design on the 1950 'English' Ford models straight away.
This is the front suspension setup we use on the Starlet. It consists of a lower control arm, a hub assembly (which holds the calliper, disk and wheel together) and the strut (shock absorber) with a spring coiled around it.
259 260
Regards,
Ivan
Note: This article may have been copied from another website and revised to better suit the Starlet community. If you are the owner of the original article and would like us to remove it, please contact me via email with the subject "Remove Article" and i will remove it from this website as soon as possible.